[100% Pass Exam Dumps] Update Latest 200-125 Dumps Cisco PDF Questions And VCE Youtube Free Demo

Update latest Cisco CCNA 200-125 dumps pdf practice questions and answers free try from lead4pass. Prepare for Cisco 200-125 exam test with best Cisco CCNA 200-125 dumps pdf files and dumps youtube demo. https://www.lead4pass.com/200-125.html dumps exam training resources. dumps exam training resources. High quality Cisco CCNA 200-125 dumps exam training materials and study guides free download, pass Cisco 200-125 exam test easily.

Latest Cisco 200-125 dumps pdf practice questions and answers: https://drive.google.com/open?id=0B_7qiYkH83VRSnZDMkVUWDJzLWM

Latest Cisco 300-360 dumps pdf practice questions and answers: https://drive.google.com/open?id=0B_7qiYkH83VRbXA1TGRTOW5TYkE

Vendor: Cisco
Certifications: CCNA
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Exam Code: 200-125
Total Questions: 966 Q&As
200-125 dumps
QUESTION 1
Which command is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?
A. transport type all
B. transport output all
C. transport preferred all
D. transport input all
Correct Answer: D

QUESTION 2
Three switches are connected to one another via trunk ports. Assuming the default switch configuration, which switch is elected as the root bridge for the spanning-tree instance of VLAN 1?
A. the switch with the highest MAC address
B. the switch with the lowest MAC address
C. the switch with the highest IP address
D. the switch with the lowest IP address
Correct Answer: B

QUESTION 3
A network administrator needs to configure a serial link between the main office and a remote location.
The router at the remote office is a non-Cisco router. 200-125 dumps How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation frame-relay
Main(config-if)# authentication chap
Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252
Main(config-if)#encapsulation ietf
Main(config-if)# no shut
Correct Answer: B

QUESTION 4
What does a Layer 2 switch use to decide where to forward a received frame?
A. source MAC address
B. source IP address
C. source switch port
D. destination IP address
E. destination port address
F. destination MAC address
Correct Answer: F

QUESTION 5
Refer to the exhibit.
200-125 dumps
Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)
A. SwitchA, Fa0/2, designated
B. SwitchA, Fa0/1, root
C. SwitchB, Gi0/2, root
D. SwitchB, Gi0/1, designated
E. SwitchC, Fa0/2, root
F. SwitchD, Gi0/2, root
Correct Answer: ABF

QUESTION 6
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?
A. This is a 10 Mb/s switch port.
B. This is a 100 Mb/s switch port.
C. This is an Ethernet port operating at half duplex.
D. This is an Ethernet port operating at full duplex.
E. This is a port on a network interface card in a PC.
Correct Answer: C

QUESTION 7
How to enable vlans automatically across multiple switches? 200-125 dumps
A. Configure VLAN
B. Confiture NTP
C. Configure each VLAN
D. Configure VTP
Correct Answer: D

QUESTION 8
What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Correct Answer: AB

QUESTION 9
Refer to the exhibit.
200-125 dumps
Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q- compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached?
A. VLANs have not been created yet.
B. An IP address must be configured for the port.
C. The port is currently configured for access mode.
D. The correct encapsulation type has not been configured.
E. The “no shutdown” command has not been entered for the port.
Correct Answer: C

QUESTION 10
A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?
A. application
B. presentation
C. session
D. transport
E. internet
F. data link
Correct Answer: A

QUESTION 11
Which three statements accurately describe Layer 2 Ethernet switches? 200-125 dumps (Choose three.)
A. Spanning Tree Protocol allows switches to automatically share VLAN information.
B. Establishing VLANs increases the number of broadcast domains.
C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information.
D. Microsegmentation decreases the number of collisions on the network.
E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port.
F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address.
Correct Answer: B,D,E

QUESTION 12
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?
A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B. Add a second router to handle the VLAN traffic.
C. Add two more Fast Ethernet interfaces.
D. Implement a router-on-a-stick configuration.
Correct Answer: D

Read more: https://www.lead4pass.com/200-125.html dumps questions and answers update free try.

Reference: http://www.examthings.com/latest-oracle-1z0-068-dumps/

Watch the video to learn more: https://youtu.be/nF4Ul2viODM