Cisco 642-892 PDF Dumps, Valid and updated Cisco 642-892 Certification Braindumps Are Based On The Real Exam

Need The Newest Cisco 642-892 Exam Dumps? Why not try Cisco 642-892 vce or pdf exam dumps? You can get all the new Cisco 642-892 exam questions and answers you need, we ensure high pass rate and money back guarantee.

QUESTION 85
Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached? (Choose three.)
A. mls qos trust override cos
B. mls qos trust cos
C. mls qos trust device cisco-phone
D. switchport priority extend cos_value
E. switchport voice vlan vlan-id

Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 86
Which three IP multicast address related statements are true? (Choose three.)
A. Multicast addresses 224.0.0.0 through 224.0.0.255 are always forwarded because they are transmitted with Time to Live (TTL) greater than 1.
B. Multicast addresses 224.0.0.5 and 224.0.0.6 are source multicast addresses for OSPF routers.
C. Multicast addresses 224.0.0.13 and 224.0.0.22 are reserved link-local addresses used by PIMv2 and IGMPv3.
D. Because they would map to overlapping IP multicast MAC addresses, multicast addresses 224.0.1.1 and 238.1.1.1 could not be used together.
E. Multicast address 224.0.1.1 has been reserved for the Network Time Protocol (NTP) by the IANA.
F.     The administratively scoped multicast addresses 239.0.0.0 through 239.255.255.255 are similar in purpose to RFC 1918 private unicast addresses.

Correct Answer: CEF Section: (none) Explanation
Explanation/Reference:
QUESTION 87
Which three statements about the EIGRP routing protocol are true? (Choose three.)
A. EIGRP sends periodic hello packets to the multicast IP address 224.0.0.9.
B. EIGRP sends periodic hello packets to the multicast IP address 224.0.0.10.
C. EIGRP supports five generic packet types, including hello, update, query, reply, and ACK packets.
D. EIGRP supports five generic packet types, including hello, database description (DBD), link-state request (LSR), link-state update (LSU), and LSAck.
E. EIGRP will form a neighbor relationship with another peer even when their K values are mismatched.
F.     EIGRP will not form a neighbor relationship with another peer when their K values are mismatched.

Correct Answer: BCF Section: (none) Explanation
Explanation/Reference: QUESTION 88
A network administrator assigns a multicast address of 239.255.8.5 to an application running on a device with an Ethernet MAC address of 01.b2.7d.05.f1.80. Which Layer 2 multicast address will this device use?
A. 01.00.5e.7F.08.05
B. 01.b2.7d.05.f1.80
C. 01.b2.7d.0a.08.05
D. 01.00.5e.05.f1.80
E. ff.ff.ff.ff.ff.ff

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 89
Refer to the exhibit. Which Catalyst switch interface command would be used to cause the switch to instruct the phone to override the incoming CoS from the PC before forwarding the packet to the switch?

A. switchport priority extend none
B. switchport priority extend trust
C. switchport priority extend cos 2
D. switchport priority extend cos 11
E. mls qos cos 2
F. mls qos cos 2 override

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 90
LAB

A.
B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 91
LAB

A. 1. Seed metric for EIGRP must have the following characteristics: Bandwidth=512 Kbps
2.
Delay=100

3.
Reliability=255

4.
Load=1

5.
MTU=1500
Seed metric for IS-IS must be set to 50.
Only redistribute Level-1 IS-IS routes into EIGRP.
Redistribute EIGPR routes into IS-IS as Level-1 routes.
Correct

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Blockade# conf t Blockade(config)# router isis Blockade(config-router)# redistribute eigrp 100 level-1 metric 50 Blockade(config)# router eigrp 100 Blockade(config-router)# redistribute isis level-1 metric 512 10 255 1 1500 Blockade(config-router)# redistribute connected
Blockade# copy run start
Answer: A
QUESTION 92
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? (Choose two.)

A. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
B. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.1
D. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
E. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.

Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 93
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2, and hosts A and B have been configured as shown. Which statement can be derived from the exhibit?

A. The GLBP weighted load balancing mode has been configured.
B. The GLBP host-dependent, load-balancing mode has been configured.
C. The GLBP round-robin, load-balancing mode has been configured.
D. The host A default gateway has been configured as 10.88.1.1/24.
E. The host A default gateway has been configured as 10.88.1.4/24.
F. The host A default gateway has been configured as 10.88.1.10/24.

Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 94
Which show command will display the two values used in the calculation of the EIGRP metric?
A. show protocol
B. show ip eigrp interface
C. show interface
D. show ip eigrp neighbor

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 95
Which two Lightweight Access Point Protocol (LWAPP) statements are true? (Choose two.)
A. Control traffic is encapsulated in UDP packets with a source port of 1024 and a destination port of 12223.
B. Control traffic is encapsulated in TCP packets with a source port of 1024 and a destination port of 12223.
C. Data traffic is encapsulated in UDP packets with a source port of 1024 and a destination port of 12223.
D. Data traffic is encapsulated in TCP packets with a source port of 1024 and destination port of 12223.
E. Layer 3 LWAPP is a UDP / IP frame that requires a Cisco Aironet AP to obtain an IP address using DHCP.
F.     LWAPP is a proprietary protocol, and because of its very high overhead it is not widely adopted .

Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 96
Which two statements are true about the Hot Standby Router Protocol (HSRP)? (Choose two.)
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
C. Routers configured for HSRP must belong to only one group per HSRP interface.
D. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
E. All routers configured for HSRP load balancing must be configured with the same priority.

Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 97
Which three WLAN statements are true? (Choose three.)
A. A lightweight AP receives control and configuration from a WLAN controller to which it is associated.
B. A WLAN client that is operating in half-duplex mode will delay all clients in that WLAN.
C. Ad hoc mode allows mobile clients to connect directly without an intermediate AP.
D. Another term for infrastructure mode is independent service set (IBSS).
E. The Aironet 1230 access point is an example of an access point that operates solely as a lightweight access point.
F.     WLANs are designed to share the medium and can easily handle an increased demand of channel contention.

Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 98
Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1?

A. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs.
B. Only redistributed RIP routes will appear in Area 1. They will be advertised via type 7 LSAs.
C. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs.
D. No redistributed routes can appear in Area 1, only summary routes.

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 99
In what three ways is QoS applied in the campus network? (Choose three.)
A. No traffic marking occurs at the core layer. Layer 2/3 QoS tags are trusted from distribution layer switches and used to prioritize and queue the traffic as it traverses the core.
B. IP precedence, DSCP, QoS group, IP address, and ingress interface are Layer 2 characteristics that are set by the access layer as it passes traffic to the distribution layer. The distribution layer, once it has made a switching decision to the core layer, strips these off.
C. MAC address, Multiprotocol Label Switching (MPLS), the ATM cell loss priority (CLP) bit, the Frame Relay discard eligible (DE) bit, and ingress interface are established by the voice submodule (distribution layer) as traffic passes to the core layer.
D. The distribution layer inspects a frame to see if it has exceeded a predefined rate of traffic within a certain time frame, which is typically a fixed number internal to the switch. If a frame is determined to be in excess of the predefined rate limit, the CoS value can be marked up in a way that results in the packet being dropped.
E. The access layer is the initial point at which traffic enters the network. Traffic is marked (or remarked) at Layers 2 and 3 by the access switch as it enters the network, or is “trusted” that it is entering the network with the appropriate tag.
F.     Traffic inbound from the access layer to the distribution layer can be trusted or reset depending upon the ability of the access layer switches. Priority access into the core is provided based on Layer 3 QoS tags.

Correct Answer: AEF Section: (none) Explanation
Explanation/Reference: QUESTION 100
Which statement about the Lightweight Access Point Protocol (LWAPP) protocol is true?
A. The processing of 802.11 data and management protocols and access point capabilities is distributed between a lightweight access point and a centralized WLAN controller.
B. LWAPP aggregates radio management forward information and sends it to a wireless LAN solution engine.
C. LWAPP authenticates all access points in the subnet and establishes a secure communication channel with each of them.
D. LWAPP advertises its WDS capability and participates in electing the best WDS device for the wireless LAN.

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 101
Which two WLAN client utility statements are true? (Choose two.)
A. In a Windows XP environment, a client adapter can only be configured and managed with the Microsoft Wireless Configuration Manager.
B. The Aironet Desktop Utility (ADU) can be used to enable or disable the adapter radio and to configure LEAP authentication with dynamic WEP.
C. The Cisco Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can both be enabled at the same time to setup WLAN client cards.
D. The Microsoft Wireless Configuration Manager can be configured to display the Aironet System Tray Utility (ASTU) icon in the Windows system tray.

Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 102
Refer to the exhibit. Which two problems are the most likely cause of the exhibited output? (Choose two.)

A. spanning tree issues
B. HSRP misconfiguration
C. VRRP misconfiguration
D. physical layer issues
E. transport layer issues

Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 103
Refer to the exhibit. Switch Cat2 is receiving IGMP frames only on interface FastEthernet 0/3. Given IGMP snooping, out of which port or ports will switch Cat2 forward multicast traffic?

A. all ports
B. none of the ports
C. FastEthernet 0/3
D. FastEthernet 0/1, 0/2, 0/4
E. FastEthernet 0/1, 0/2, 0/3, 0/4
F. FastEthernet 0/1, 0/2, 0/4, 0/5, 0/6, 0/7, 0/8

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 104
Refer to the exhibit. Which statement is true about the voice traffic coming to the switch access port that is connected to the IP phone?

A. The voice VLAN must be configured as a native VLAN on the switch.
B. The traffic on the voice VLAN must be tagged with 802.1p encapsulation in order to coexist on the same LAN segment with a PC.
C. A PC connected to a switch port via an IP phone must support a trunking encapsulation.
D. A PC connected to a switch port via an IP phone is unaware of the presence of the phone.
E. To improve the quality of the voice traffic, no other devices should be attached to the IP phone.

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 105
Which three are characteristics of IPv6? (Choose three.)
A. An IPv6 address is 128 bits long.
B. An IPv6 header is 20 bits long.
C. An IPv6 header contains the next header field.
D. An IPv6 header contains the protocol field.
E. IPv6 routers send RA messages.
F. An IPv6 header contains the header checksum field.

Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:

If you fail in Cisco 642-892 exam test with Cisco 642-892 exam dumps, we promise to give you full refund! You only need to scan your Cisco 642-892 test score report to us together with your receipt ID. After our confirmation, we will give you full refund in time.Or you can choose to charge another IT exam Q&As instead of Cisco 642-892 exam dumps.Useful Cisco certifications exam dumps are assured with us.If our Cisco 642-892 exam dumps can’t help you pass Cisco 642-892 exam,details will be sent before we send the exam to you.We don’t waste our customers’ time and money! Trusting Passtcert is your best choice!