Category: Cisco
Cisco 642-892 Practice Test, Buy software Cisco 642-892 Exam Questions Vce Latest Version PDF&VCE
100% Valid:How to choose the right Cisco 642-892 exam dumps? Just try the Flydumps newest Cisco 642-892 exam dumps with more new added quesitons and answers,also now you can free download Cisco 642-892 VCE player and PDF files for training.
UESTION 1
When an IPv6 enabled host boots, it sends a router solicitation (RS) message.
An IPv6 router responds with a router advertisement (RA). Which two items are contained in the RA? (Choose two.)
A. IPv6 address for the host
B. lifetime of the prefix
C. prefixes for the link
D. keepalive timers
E. request for the local host IP address
F. any route advertisements it has received
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Refer to the exhibit. Which switch interface configuration command would automatically configure quality of service (QoS) for voice over IP (VoIP) within a QoS domain?
A. auto qos voip cisco-phone
B. mls qos trust
C. switchport priority extend cos 7
D. switchport priority extend trust
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 3
In the use of 802.1X access control, which three protocols are allowed through the switch port before authentication takes place? (Choose three.)
A. STP
B. CDP
C. EAP MD5
D. TACACS+
E. EAP-over-LAN F. protocols not filtered by an ACL
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 4
Which protocol specified by RFC 2281 provides network redundancy for IP networks, ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits?
A. STP
B. IRDP
C. ICMP
D. HSRP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Which two statements about the IS-IS routing protocol are true? (Choose two.)
A. In the IS-IS routing domain, routers may have adjacencies with other routers on multipoint links.
Cisco 642-892 Cert,Buy Discount Cisco 642-892 Answers Latest Version PDF&VCE
Attention Please:Professional new version Cisco 642-892 PDF and VCE dumps can now free download on Flydumps.com,all are updated timely by our experts covering all Cisco 642-892 new questions and questions.100 percent pass your exam.
Exam A QUESTION 1
Based on the exhibited command output, which two statements are true? (Choose two.)
A. The EIGRP network is stable.
B. The router at 10.1.1.3 has not replied to the R1 query packet.
C. The route to 172.19.0.0/16 is undergoing recomputation.
D. The route to 172.19.0.0/16 is stuck-in-active.
E. R1 has sent a query packet to 10.1.1.2.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Which two multicast IP addresses can be represented by the multicast MAC address 0100.5e0A.0A07? (Choose two.)
A. 228.10.10.7
B. 228.10.10.8
C. 228.10.138.7
D. 229.11.10.7
E. 229.138.10.7
F. 229.138.10.8
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Which statement is true about EBGP?
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. A static route can be used to form an adjacency between neighbors.
D. EBGP requires a full mesh.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 4
Which statement is true about 802.1x port-based authentication?
A. Hosts are required to have a 802.1x authentication client or utilize PPPoE.
B. Before transmitting data, an 802.1x host must determine the authorization state of the switch.
C. RADIUS is the only supported authentication server type.
D. TACACS+ is the only supported authentication server type.
E. If a host initiates the authentication process and does not receive a response, it assumes it is not authorized.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Which three statements are true about the Internet Group Management Protocol (IGMP)? (Choose three.)
A. IGMP is a multicast routing protocol that makes packet-forwarding decisions independent of other routing protocols such asEIGRP.
» Read more about: Cisco 642-892 Cert,Buy Discount Cisco 642-892 Answers Latest Version PDF&VCE »
Cisco 642-832 Certification Material Provider, Latest Updated Cisco 642-832 Preparation Materials On Our Store
Flydumps ensures Cisco 642-832 study guide are the newest and valid enough to help you pass the test.Please visit Flydumps.com and get valid Cisco 642-832 PDF and VCE exam dumps with free new version.100% valid and success.
Exam A
QUESTION 1
The following commands are issued on a Cisco Router:
Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router(configuration)#exit
Router#debug ip packet 199
What will the debug output on the console show?
A. All IP packets passing through the router
B. Only IP packets with the source address of 10.1.1.1
C. All IP packets from 10.1.1.1 to 172.16.1.1
D. All IP Packets between 10.1.1.1 and 172.16.1.1
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
In this example, the “debug ip packet” command is tied to access list 199, specifying which IP packets
should be debugged. Access list 199 contains two lines, one going from the host with IP address 10.1.1.1
to 172.16.1.1 and the other specifying all TCP packets from host 172.16.1.1 to 10.1.1.1.
QUESTION 2
What level of logging is enabled on a Router where the following logs are seen?
%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
A. alerts
B. critical
C. errors
D. notifications
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
Cisco routers, switches, PIX and ASA firewalls prioritize log messages into 8 levels (0-7), as shown below: LevelLevel NameDescription 0 Emergencies System is unusable 1 Alerts Immediate action needed 2 Critical Critical conditions 3 Errors Error conditions 4 Warnings Warning conditions 5 Notifications Informational messages 6 Informational Normal but significant conditions 7 Debugging Debugging messages
When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case we can see that logging level of 3 (as seen by the 3 in “LINK-3- UPDOWN”) and level 5 (as seen by the 5 in “LINEPROTO-5-UPDOWN”) are shown, which means that logging level 5 must have been configured. As shown by the table, logging level 5 is Notifications.
Cisco 642-832 Exam Demo, Help To Pass Cisco 642-832 Real Exam Will Be More Popular
The 100% valid latest Cisco 642-832 question answers ensure you 100% pass! And now we are offering the free Cisco 642-832 new version along with the VCE format Cisco 642-832 practice test. Free download more new Cisco 642-832 PDF and VCE on Flydumps.com.
Testlet 1
TSHOOT 642-832
TICKET NUMBER 1
CLICK NEXT FOR THE TOPOLOGY & SHOW RUNNING CONFIG
AGAIN CLICK NEXT FOR THE QUESTIONS WHERE YOU WE WILL ALSO GET TOVIEW TOPOLOGY & DEVICE CONFIG
AFTER ANSWERING THE FIRST TICKET CLICK ON ‘END’ FOR THE NEXT TICKET.
ASW1
!
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ASW1
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 5
ip cef
!
!
no ip domain lookup
ip domain name lab.local
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
interface Port-channel13 switchport trunk native vlan 200switchport mode trunkswitchport trunk allowed vlan 1-9,10-20,200
!
interface Port-channel23 switchport trunk native vlan 200switchport mode trunkswitchport trunk allowed vlan 1-9,10-20,200
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/1no ip addressshutdown duplex autospeed auto
!
!
!
interface FastEthernet1/0/1switchport access vlan 10spanning-tree portfastswitchport port-security
!
Cisco 642-832 certifications Dump, Free Download Real Cisco 642-832 Exam With New Discount
ATTENTION: Get your Cisco 642-832 certification easily with，Flydumps latest Cisco 642-832 exam dumps. All the up-to-date questions and answers were added to the new version. Go to the site Flydumps.com to get more Cisco 642-832 exam
information.
Exam A
QUESTION 1
Which two statements about the Cisco Aironet Desktop Utility (ADU) are true? (Select two)
A. The Aironet Desktop Utility (ADU) profile manager feature can create and manage only one profile for the wireless client adapter.
B. The Aironet Desktop Utility (ADU) can support only one wireless client adapter installed and used at a time.
C. The Aironet Desktop Utility (ADU) can be used to establish the association between the client adapter and the access point, manage authentication to the wireless network, and enable encryption.
D. The Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can be used at the same time to configure the wireless client adapter.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 2
At which layer of the OSI model does the Spanning Tree Protocol (STP) operate at?
A. Layer 5
B. Layer 4
C. Layer 3
D. Layer 2
E. Layer 1
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 3
In computer networking a multicast address is an identifier for a group of hosts that have joined a multicast group. Multicast addressing can be used in the Link Layer (OSI Layer 2), such as Ethernet Multicast, as well as at the Internet Layer (OSI Layer 3) as IPv4 or IPv6 Multicast. Which two descriptions are correct regarding multicast addressing?
A. The first 23 bits of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
B. The last 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
C. To calculate the Layer 2 multicast address, the host maps the last 23 bits of the IP address into the last 24 bits of the MAC address. The high-order bit is set to 0.
D. The first 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
Cisco 642-813 Exam Collection, Latest Release Cisco 642-813 Answers Latest Version Cisco 642-813 PDF&VCE
Important Info — Cisco 642-813 new study guide are designed to help you pass the exam in a short time.Everything you need can be found in the new version Cisco 642-813 exam dumps.Visit Flydumps.com to get more valid information.
Exam A
QUESTION 1
Acme is a small export company that has an existing enterprise network comprised of 5 switches;
CORE,DSW1,DSW2,ASW1 and ASW2. The topology diagram indicates their desired pre-VLAN spanning
tree mapping.
Previous configuration attempts have resulted in the following issues:
每
CORE should be the root bridge for VLAN 20; however, DSW1 is currently the root bridge for VLAN 20.
每
Traffic for VLAN 30 should be forwarding over the gig 1/0/6 trunk port between DSW1 and DSW2. However VLAN 30 is currently using gig 1/0/5.
每
Traffic for VLAN 40 should be forwarding over the gig 1/0/5 trunk port between DSW1 and DSW2. However VLAN 40 is currently using gig 1/0/6.
You have been tasked with isolating the cause of these issuer and implementing the appropriate solutions. You task is complicated by the fact that you only have full access to DSW1, with isolating the cause of these issues and implementing the appropriate solutions. Your task is complicated by the fact that you only have full access to DSW1, with the enable secret password cisco. Only limited show command access is provided on CORE, and DSW2 using the enable 2 level with a password of acme. No configuration
\
Correct Answer: configure terminal spanning-tree vlan 20 priority 61440 interface g1/0/6 spanning-tree vlan 30 port-priority 64 exit interface g1/0/5 spanning-tree vlan 40 cost 1 show spanning-tree copy run start
Section: (none) Explanation
Explanation/Reference:
By using the ※show spanning-tree§ command as shown above, we learned that DSW1 is the root bridge for VLAN 20 (notice the line ※This bridge is the root§
To determine the root bridge, switches send and compare their priorities and MAC addresses with each other. The switch with the lowest priority value will have highest priority and become the root bridge. Therefore, we can deduce that the priority of DSW1 switch is lower than the priority of the CORE switch so it becomes the root bridge. To make the CORE the root bridge we need to increase the DSW1∩s priority value, the best value should be 61440 because it is the biggest value allowed to assign and it will surely greater than of CORE switch. (You can use another value but make sure it is greater than the CORE priority value by checking if the CORE becomes the root bridge or not; and that value must be in incrementsof 4096).
Free Sharing –pass the Cisco 642-813 exam quickly
100% Valid And Pass With latest Cisco 642-813 exam dumps, you will never fail your Cisco 642-813 exam. All the questions and answers are updated and added to the new version timely by our experts.Also now Cisco 642-813 is offering free Cisco 642-813 exam VCE player and PDF files for free on their website.
Exam A
QUESTION 1
VTP devices in a network track the VTP revision number. What is a VTP configuration revision number?
A. A number for identifyiing changes to the network switch
B. A number for identifying changes in the network router
C. A number for identifying changes to the network topology
D. none of the other alternatives apply
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
The configuration revision number is a 32 bit number that indicates the level of revision for a VTP packet.
Each VTP device tracks the VTP configurationa revision number assigned to it, and most of the VTP
packets contain the VTP configuration revision number of the sender.
This information is used to determine whether the received information is more recent that the current
revision of a switch, change the VTP domain name and then change it back to the original name.
QUESTION 2
Refer to the exhibit. VLAN 1 and VLAN 2 are configured on the trunked links between Switch A and Switch B Port Fa0/2 on Switch B is currently in a blocking state for both VLANs. What should be done to load the balance VLAN traffic between Switch A and Switch B?
Correct Answer: B Section: (none)Explanation
QUESTION 3
What must be configured on a Cisco switch in order to advertise VLAN information
A. VTP mode B. VTP password
C. VTP revision number
D. VTP pruning
E. VTP domain name
F. none of the other alternatives apply
Correct Answer: E Section: (none) Explanation
QUESTION 4
A. This interface is a member of a voice VLAN
B. This interface is configured for access mode
C. this interface is a dot1q trunk passing all configuration
D. this interface is a member of VLAN 7
E. this interface is a member of VLAN 1
Correct Answer: BD Section: (none)Explanation
QUESTION 5
Correct Answer: ABCD Section: (none) Explanation
QUESTION 6
A. STP root status
B. VTP mode
C. Negotiation status
D. Management domain
E. Configuration revision number
Correct Answer: DE Section: (none)Explanation
QUESTION 7
A. Client
B. server
C. transparent
D. pass-through
E. no-negociate
Correct Answer: BC Section: (none) Explanation
QUESTION 8
Correct Answer: B Section: (none) Explanation
QUESTION 9
A. 802.1Q tunneling
B. ATM
C. SDH
D. IP over Optical Networking
E. ISL
Correct Answer: A Section: (none)Explanation
QUESTION 10
A. VLAN 1-5 will use fa0/10 as a backup only
B. VLAN 6-10 will use fa0/10 as a backup only
C. VLAN 1-5 will be blocking if fa0/10 goes down
D. VLAN 1-10 are configured to load share between fa0/10 and fa0/12
E. VLAN 6-10 have a port priority of 128 on fa0/10
Correct Answer: BD Section: (none)Explanation
QUESTION 11
A. supports token ring VLANs
B. allows VLAN consistency checks
Correct Answer: AB Section: (none) Explanation
QUESTION 12
A. DTP packets are sent to switch b
B. the native VLAN for switch b is vlan 1
C. a trunk link will be formed
D. DTP is not running on switch a
E. only VLANs 1 – 1001 will travel across the trunk link
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Correct Answer: D Section: (none) Explanation
QUESTION 14
A. VTP version 2 supports token ring VLANs
B. VTP version 2 allows VLAN consistency checks
C. VTP version 2 allows active redundant links when used with spanning tree
D. VTP version 2 reduces the amount of configuration necessary
E. VTP version 2 saves VLAN configuration memory
Correct Answer: AB Section: (none) Explanation
QUESTION 15
What does the global command udld enable accomplish?
» Read more about: Free Sharing –pass the Cisco 642-813 exam quickly »
Cisco 642-813 Answers, The Most Recommended Cisco 642-813 Exam Practice PDF Online Store
New VCE and PDF – You can prepare Cisco 642-813 exam in an easy way with Cisco 642-813 questions and answers. By training our Cisco 642-813 vce dumps with all the latest questions, you can pass the exam in the first attempt.
Exam A QUESTION 1
Refer to the exhibit. What is the effect on the trust boundary of configuring the command mls qos trust cos on the switch port that is connected to the IP phone?
A. Effectively the trust boundary has been moved to the IP phone.
B. The host is now establishing the CoS value and has effectively become the trust boundary.
C. The switch is rewriting packets it receives from the IP phone and determining the CoS value.
D. The switch will no longer tag incoming voice packets and will trust the distribution layer switch to set the CoS.
E. RTP will be used to negotiate a CoS value based upon bandwidth utilization on the link.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Refer to the exhibit. What is the effect when the switchport priority extend cos 3 command is configured
on the switch port interface connected to the IP phone?
A. Effectively, the trust boundary has been moved to the PC attached to the IP phone.
B. The computer is now establishing the CoS value and has effectively become the trust boundary.
C. The IP phone is enabled to override with a CoS value of 3 the existing CoS marking of the PC attached CareerCert.blogspot.com to the IP phone.
D. The switch will no longer tag incoming voice packets and will extend the trust boundary to the distribution layer switch.
E. RTP will be used to negotiate a CoS value based upon bandwidth utilization on the link.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Which three WLAN statements are true? (Choose three.)
A. A lightweight AP receives control and configuration from a WLAN controller to which it is associated.
B. A WLAN client that is operating in half-duplex mode will delay all clients in that WLAN.
C. Ad hoc mode allows mobile clients to connect directly without an intermediate AP.
D. Another term for infrastructure mode is independent service set (IBSS).
E. The Aironet 1230 access point is an example of an access point that operates solely as a lightweight access point.
F. WLANs are designed to share the medium and can easily handle an increased demand of channel contention.
Studying The Latest Version Cisco 642-661 Braindumps Pass Exam Easily
Fully Updated Do not hesitate to choose Flydumps Cisco 642-661 VCE Exam Dumps, all are updated timely by SAP expert professionals. Visit the site Flydumps.com to get the free Cisco 642-661 pdf dumps and free vce player.
Exam A QUESTION 1
Look at the picture.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
Answer: Check certifyme eEngine, Download from Member Center
QUESTION 2
What are two purposes of the BGP scan-time command? (Choose two.)
A. to tune the BGP process which walks the BGP table and confirms the reachability of next hops
B. to allow faster detection of downed BGP peers
C. to improve BGP convergence time
D. to tune the BGP update interval
E. to decrease the effects of unstable routes by increasing the route suppression time
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Which command is used to configure the external, confederation-wide AS number?
A. router(config)#router bgp {as-number}
B. router(config-router)#bgp confederation peers {as-number}
C. router(config-router)#bgp confederation identifier {as-number}
D. router(config-router)#bgp cluster-id {as-number}
E. router(config-router)#neighbor {ip address} remote-as {as-number}
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 4
When creating iBGP multipaths which three criteria must be met by multiple paths to the same destination? (Choose three.)
A. Router IDs must be the same on all routers.
B. Each destination must have a different next-hop address.
C. The destination AS-number must be different for each destination.
D. Multi-exit discriminator attributes must be the same on all paths.
E. Interior Gateway Protocol distance must be identical on each path.
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Lab
A.
» Read more about: Studying The Latest Version Cisco 642-661 Braindumps Pass Exam Easily »
Real Cisco 642-661 Exam Questions Updated All New Added Questions
Attention Please: Professional new version Cisco 642-661 PDF and VCE dumps can now free download on Flydumps.com all are updated timely by our experts covering all new questions and questions.100 percent pass your Cisco 642-661 exam.
Exam A
QUESTION 1
Exhibit: Certkiller router#show ip route Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2 E1 – OSPF external type 1, E2 – OSPF external type 2, EEGP i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, * -candidate default U – per-user static route, o – ODR T – traffic engineered route Gateway of last resort is not set 172.16.0.0/24 is subnetted, 2 subnets B 172.16.10.0 [20/0] via 10.1.1.100, 00:00:24 B 172.16.11.0 [20/0] via 10.1.1.100, 00:00:24 172.26.0.0/28 is subnetted, 3 subnets B 172.26.1.48 [200/0] via 192.168.1.50, 00:00:31 B 172.26.1.32 [200/0] via 192.168.1.50, 00:00:31 B
172.26.1.16 [200/0] via 192.168.1.50, 00:00:31 10.0.0.0/8 is variable subnetted, 2 subnets, 2 masks B 10.0.0/8 [20/0] via 10.1.1.100, 00:00:24 C 10.1.1.0/24 is directly connected, Serial3 192.168.1.0/28 is subnetted, 3 subnets C 192.168.1.32 is directly connected, Serial1 C 192.168.1.48 is directly connected, Serial2 C 192.168.1.16 is directly connected, Serial0 192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks B 192.168.2.64/28 [20/0] via 10.1.1.100,
00:00:26
Based on the show ip route output in the exhibit, how can you tell if a BGP route is learned via IBGP or EBGP?
A.
By the Metric
B.
By the Next Hop
C.
By the Admin Distance
D.
By the code “B” or “B Ex”
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation: admin distance. Distance of EBGP is 20, Distance of IBGP is 200.
QUESTION 2
What is the range of values from which an ISP can assign a private AS number?
A. 32768 to 65535
B. 64512 to 65535
C. 65101 to 65535
D. 65001 to 65535
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation: An autonomous system (AS) is a collection of networks under a single technical administration. Some other definitions refer to a collection of routers or IP prefixes, but in the end they all mean the same entity. The important principle is the technical administration, which means sharing the same routing protocol and routing policy. Legal and administrative ownership of the routers does not matter in terms of autonomous systems. Autonomous systems are identified by AS numbers, 16-bit unsigned quantities ranging from 1 to 65535. Public AS numbers are assigned by Internet registries. For customers that need AS numbers to run BGP in their private networks, a range of private AS numbers (64512 – 65535) has been reserved. Reference: Configuring BGP on Cisco Routers volume 1 p.2-4
QUESTION 3
Network topology exhibit
What can prevent the corresponding BGP session from being successfully established?
» Read more about: Real Cisco 642-661 Exam Questions Updated All New Added Questions »
